View UFL-LP-062-A_642395.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ultra Small SMT Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height
U.FL Series
Meets up to 6 GHz Requirement
Mated Height Comparison (With Hirose Product)
U.FL-LP-040 U.FL-LP-066 1.9(2.0Max) 2.4(2.5Max) 3(3.2Max) U.FL-LP(V)-040
E.FL-LP-040 E.FL-LP-066
U.FL Series
E.FL Series
sFeatures
1. Low Profile: 1.9mm or 2.4mm Nom. Mated Height
Height from the circuit board is 2.0mm or 2.5mm maximum when a plug (right angle) is mated to a receptacle, which ranks with world's smallest class.
qSpace Factor of Mated Connector
U.FL-LP-040 2.5Max Dia.0.81 U.FL-R-SMT U.FL-LP-066 2.5Max Dia.1.32 Dia.1.13 U.FL-R-SMT U.FL-LP(V)-040 Dia.0.81 U.FL-R-SMT U.FL-LP-062 Dia.1.0 U.FL-R-SMT U.FL-LP-088 Dia.1.37 U.FL-R-SMT
2.Extremely Small Occupied Mounting Area
In comparison with our SMT coaxial connectors E.FL series, the receptacle provides a reduction of approximately 18% of occupied mounting surface, which is only 7.7mm2.
3.Light Weight
One of the world's lightest coaxial connectors. Receptacle: 15.7mg
4.Applicable Up to 6 GHz Frequency
To meet the frequency requirements of a wide variety of miniature equipment, these connectors offer high frequency performance from DC to 6 GHz.
5.Board placement with automatic equipment
Supplied on tape-and-reel packaging.
NEW
2.0Max
6.Use of Ultra-fine Teflon Cable
From among the types of applicable cable, dia. 0.81mm(single shielded) ultra-fine Teflon coaxial cable has been made a standard specification in construction area. Refer to the following pages for different cable types.
7.Simple Removal of Connector
The extraction jig permits simple removal of connectors.
NEW
2.4Max
8.User Friendly Mating Operation
Tactile lock feeling ensures engagement even with this small size.
sApplications
Mobile phones, Wireless LAN, Mini-PCI, Bluetooth, PDA, GPS, electronic measuring instruments, etc.
NEW
2.4Max
2003.9
1
s Product Specifications
Ratings
Nominal characteristic impedance Voltage rating Frequency range 50 ohms 60 V AC (rms) DC to 6 GHz Operating temperature range Operating humidity -40C to +90C 90% max.
Item
1. Contact resistance
Specification
Center: 20 m ohms max. Outside: 10 m ohms max. 10 mA max. 100 V DC 200 V AC / 1 minute Up to 3GHz 1.3 Max 1.3 Max 1.3 Max 1.3 Max 1.3 Max 1.3 Max
Conditions
2. Insulation resistance 3. Withstanding voltage 4. V.S.W.R.*
500 M ohms min. No flashover or insulation breakdown. Part No. U.FL-LP-040 dia.0.81mm Coaxial Cable Assembly U.FL-LP(V)-040 dia.0.81mm Coaxial Cable Assembly U.FL-LP-066 dia.1.13mm Coaxial Cable Assembly U.FL-LP-066 dia.1.32mm Coaxial Cable Assembly U.FL-LP-062 dia.1mm Coaxial Cable Assembly U.FL-LP-088 dia.1.37mm Coaxial Cable Assembly
3 to 6GHz 1.35 Max 1.3 Max 1.4 Max 1.5 Max 1.3 Max 1.4 Max
5. Female contact holding force 0.15 N min. 6. Durability (mating/un-mating, with corresponding plug) 7. Vibration No electrical discontinuity of 1s min. 8. Shock No damage, cracks or parts dislocation. Contact resistance Center: 25 m ohms max. Outside: 15 m ohms max.
Measured with a O 0.475 pin gauge
30 cycles
Frequency: 10 to 100 Hz, single amplitude of 1.5mm, acceleration of 59m/s2, for 5 cycles in the direction of each of the 3 axis. Acceleration of 735 m/s2, 11ms duration, sine half-wave waveform, 2 cycles in each of 3 axes.
9. Humidity (Steady state)
No damage, cracks or parts dislocation. Insulation resistance 100 M ohms min.(when humidity high) 96 hours at temperature of 40c and humidity of 95%. Insulation resistance 500 M ohms min.(when dry)
10. Temperature cycle
No damage, cracks or parts dislocation. Contact resistance:25 m ohms max. (Center) 15 m ohms max. (Outside)
Temperature:-40C/+5 to +35C/+90C/+5 to +35C Time: 5 cycles 5% salt water solution, 48 hours 30
/ 5 max.
/30
/5 max.(Minutes)
11. Salt spray test
No excessive corrosion
*V.S.W.R. Measurement System The above V.S.W.R. standard values were measured using the measurement system of the diagram below.
Note 1: Cable type connectors were measured with SMA conversion adapters attached to both ends of the harness product of a suitable 100cm cable. Note 2: Board type connectors were mounted to a 50 glass epoxy board and measurements were conducted with SMA conversion adapters attached.
sMaterials
Part Shell Male center contact Female center contact Insulator Plug Receptacle Material Phosphor bronze Brass Phosphor bronze PBT LCP Finish Silver plating Gold plating Gold plating Color: Black Color: Beige Remarks ---------- ---------- ---------- UL94V-0 UL94V-0
2
sCable Assembly (Plug)
U.FL-LP-040 U.FL-LP-066 U.FL-LP(V)-040 U.FL-LP-062 U.FL-LP-088
2.8
2.8
3
Part No.
4 1.93 1.93 4 1.5 3.4 1.8
3
4 1.85
3
5
Mated Height
2.5mm Max. (2.4mm Nom.) Dia. 0.81mm Coaxial cable 53.7
2.5mm Max. (2.4mm Nom.) Dia. 1.13mm and Dia. 1.32mm Coaxial cable 59.1
2.0mm Max. (1.9mm Nom.) Dia. 0.81mm Coaxial cable 34.8
2.4mm Max. (2.3mm Nom.) Dia. 1mm Coaxial cable 45.5
2.4mm Max. (2.3mm Nom.) Dia. 1.37mm Coaxial cable 71.7
Applicable cable Weight (mg)
qCable Guide
Description
Dia.0.81mm Coaxial Cable Dia.1.13mm Coaxial Cable Dia.1.32mm Coaxial Cable Dia.1mm Coaxial Cable Dia.1.37mm Coaxial Cable
CableDia. 0.81mm Inner TypeCoaxial cable * Conductor
04 7/0.05 SA (AWG36) 7/0.08 SA (AWG32) 7/0.08 SA (AWG32) 7/0.071 SA (AWG33) 7/0.102 SA (AWG30)
Cable Specification
Dia. 0.81mm Dielectric
Outer
Single Shield SA Single
Coaxial Diameter cableConductor* Dia.0.40 PFA Dia.0.68 FEP Dia.0.66 FEP Dia.0.62 FEP Dia.0.88 FEP
Jacket Diameter
Dia.0.81 PFA Dia.1.13 FEP Dia.1.32 FEP Dia.1 FEP Dia.1.37 FEP
Dia. Nominal Dia. 1.37mm attenuation Nominal 1mm Coaxial cable Coaxial cable Impedance At 3GHz At 6GHz 50 ohms 6.45dB/m 3.43dB/m [3.73dB/m] 3.8dB/m 9.42dB/m 5.13dB/m [5.44dB/m] 5.6dB/m
068
Shield SA[TA] Double Shield TA Tape, single Shield TAT Single Shield TA
50 ohms
066
50 ohms
062
50 ohms
3.1dB/m
4.4dB/m
088
50 ohms
2.8dB/m
4.3dB/m
(data as provided by material suppliers, for reference only) * SA : Silver plated annealed copper wire, TA : Tin plated annealed copper wire, TAT : Tin plated copper wire alloyed with tin
sHow to Specify Cable Assembled Plug
Dimension of U.FL Series assembly products should be made as indicated below. Double-Ended Cable Assembly
L
Single-Ended Cable Assembly
L
qOrdering Information
qTotal Standard Tolerance for Total Length of Cable Assembly
3 4
Total Length(mm) 00350U.FL - [] LP - [] - A - (L)
1 1 Series name 2 Assembly type 3 Cable type 2
U.FL LP: Single ended 2LP: Double ended 04 : Dia.0.81mm Coaxial Cable 068 : Dia.1.13mm Coaxial Cable 066 : Dia.1.32mm Coaxial Cable 062 : Dia.1 mm Coaxial Cable 088 : Dia.1.37mm Coaxial Cable Length is expressed in mm units.
4 Total Length(mm)
Please contact Hirose Sales Representative for cable length and cable end treatment.
3
sReceptacles
Cut Out Prohibition Area GND SIG 2.2 0.05 GND SIG 1 0.05 O2 1.25 1.2Max(NOTE 3) GND 0.05 GND 4 0.05 1.9 0.05
0.35
Note 1: Receptacles of (01) specification are sold by the pack with 100 pieces per pack. Please order in pack units. Note 2: Receptacles of (10) specification are sold by the reel (which contains 2,500 pieces). Please order in reel units. Note 3: Permissible value for mold resin which gets onto the center contact. Part No. U.FL-R-SMT(01) U.FL-R-SMT(10) CL No. 331-0471-0-01 331-0471-0-10
(3.1)
2.6 1.8
Recommended PCB Footprints
Packaging Bag packaging (100 pieces/bag) Reel packaging (2500 pieces/reel)
Weight (mg) 15.7/unit
qPackaging Specifications
Embossed Carrier Tape Dimensions
0.1
1.75
2
0.1
4
0.1
Center contact
0.3
0.3
12
5.5
0.1
8
0.1
Unreeling direction
Reel Dimensions
1.8 14
O13
O21
4
O330
2
1.05 0.05 1.6
3 2.6 0.6
1
O1 .5
1 0. +0
sConversion Adapter
qSMA Conversion Adapter (Mating portion: U.FL side jack - SMA side plug)
1.1 (10.7) 8HEX
Note: The U.FL side mating portions has a lower lock retention force than the regular product, therefore, cannot be used for purposes other than performance measurements.
O1.9
Part No. HRMP-U.FLJ
CL No. 311-0300-2
qSMA Conversion Adapter (Mating portion: U.FL side plug - SMA side jack)
6
14.05 (4.05)
5.6
1/4-36UNS-2A
Note: The U.FL side mating portions has a lower lock retention force than the regular product, therefore, cannot be used for purposes other than performance measurements.
Part No. HRMJ-U.FLP
(18.6) 6 (4)
311-0301-5
qSMA Conversion Adapter (Mating portion: U.FL side plug-SMA side jack)
O6.35
CL No.
5.5
1/4-36UNS-2A
Part No. Note: This connector is used by compressing the mated portion of U.FL side onto the U.FL-R-SMT portion. HRMJ-U.FLP-ST1
12.9 (7.9) (4.4) 5 1
CL No. 311-0385-5
sReceptacle for Check
This receptacle is used for inspecting the continuity, withstand voltage, and other aspects of the harness product.
7HEX
M5
0.5
Part No. This receptacle is used for check the continuity, withstanding voltage, and other performance of the cable assembly products. U.FL-R-1
CL No. 331-0466-0
(90)
sExtraction Jig
This jig is used for extraction from a mating condition.
5
U.FL
Note: Part No. U.FL-LP-N-2 for U.FL-LP-040/066/088. Part No. U.FL-LP(V)-N-2 for U.FL-LP(V)-040/U.FL-LP-062.
2.1
Part No. U.FL-LP-N-2 U.FL-LP(V)-N-2
CL No. 331-0494-5 331-0493-2
O15
50
5
sUsage Precautions
1. Plugs
1) To disconnect connectors, hook the end portion of U.FL-LP-N-2 and U.FL-LP(V)-N-2 onto the connector cover and pull off vertically in the direction of the connector mating axis. 1) To remove the connector directly, hold the connector cover and pull off Extraction Jig vertically in the direction of the connector mating axis. U.FL Cable (Please exercise caution so as not to injure fingertips or nails.) Assembly 2) To mate the connectors, the mating axes of both connectors are aligned and the connectors are inserted as perpendicularly as possible. Do not attempt to insert on an extreme angle.
U.FL-R-SMT
(1) Connection/ disconnection of connectors
After the connectors are mating, do not apply a load to the cable in excess of the values indicated in the diagram below.
U.FL-LP-040 U.FL-R-SMT 4N max. 2N max.
(2) Permissible load on the cable after connector mating.
2N max.
(3) Precautions
Do NOT forcefully twist or deform wires.
2. Receptacles
(1) Recommended temperature profile (Reference)
() 260 240 220 200 180 160 140 120 100 80
Heating peak 240 3 seconds
Temperature on Top Portion of Part
Preheating (130 to 165
183 ) 40 to 50 seconds
Within 2 minutes
Time
1) The temperature profile indicates the board surface temperature at the point of contacts with the connector terminals (for surface mounted receptacle). 2) The temperature profile will change depending on conditions which include such factors as the size of the board, the solder used, and the solder thickness. (2) Recommended manual soldering (Reference) Manual soldering: 350C for 5 seconds
(3) Recommended screen 0.1 to 0.15 mm thickness
6
NOTES :
7
USA: HIROSE ELECTRIC U.S.A., INC. 2688 Westhills Court, Simi Valley, CA 93065-6235 Phone : 1 805 522 7958 Fax : 1 805 522 3217 http://www.hirose.com
EUROPE BRANCH: HIROSE ELECTRIC CO., LTD. Beechavenue 46.1119PV Schiphol-Rijk,The Netherlands Phone : 31 20 6557460 Fax : 31 20 6557469 http://hiroseeurope.com
GERMANY: HIROSE ELECTRIC GmbH Zeppelinstrasse 42 D-73760 Ostfildern Kemnat Phone : 49 711 4560021 Fax : 49 711 4560729 http://www.hirose.de CHINA: HIROSE ELECTRIC TRADING(SHANGHAI) CO., LTD. 3705,Bund Center,222 Yan An Road(E),Shanghai 20002 Phone : 86 21 6335 2538 Fax : 86 21 6335 0767
UNITED KINGDOM: KOREA: HIROSE ELECTRIC UK LTD. HIROSE KOREA CO., LTD. Crownhill Business Centre 22 Vincent Avenue (#2NA311,Shihwa Industrial Complex), Crownhill, Milton Keynes MK8 OAB 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do Phone : 44 1908 305400 Phone : 82 31 496 7000,7124 Fax : 44 1908 305401 Fax : 82 31 496 7100 http://www.hirose.co.uk http://www.hirose.co.kr HONG KONG: HIROSE ELECTRIC CO., LTD. Unit 506, Energy Plaza. 92 Granville Road, Tsim Sha Tsui East, Kowloon Phone : 852 2803 5338 Fax : 852 2591 6560 TAIWAN: HIROSE ELECTRIC CO., LTD. No.28 Lane 247 Sec. 2 Yen Ping N,Rd.Taipei Phone : 886 2 2557 7351,7352 Fax : 886 2 2552 9851
SINGAPORE: HIROSE ELECTRIC CO., LTD. 10 Anson Road #34-13 International Plaza 079903 Phone : 65 6324 6113 Fax : 65 6324 6123
(R)
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933
8
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.

▲Up To Search▲

Price & Availability of UFL-LP-062-A

	To Download UFL-LP-062-A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .